You are switching manufacturers. The mold is being packed and shipped to a new facility, and your plan assumes production will restart on schedule.
What this plan rarely accounts for is the condition the mold arrives in, because tooling that has been running sick for months looks identical on the outside to properly maintained tooling.
The difference shows up two to four weeks into the inspection process, sometimes longer, and by then, the launch schedule you built around a clean handover is already under pressure.
Why the Problem Was Already There Before You Switched
The mold did not degrade during the transfer. It degraded across thousands of cycles during the previous production run as wear accumulates quietly, and reject rates are the last indicator to move. By the time quality problems appear in your incoming inspection, the mold has usually been in poor condition for a long time.
This is a visibility problem, not a manufacturer change problem, and the next manufacturer inherits whatever the previous one left behind.
The Number That Changes How You Think About This

At Wanox, every customer mold runs on a documented preventive maintenance schedule, with checks performed every 50,000 cycles. On one automotive program, a scheduled check at 600,000 cycles revealed electrical erosion and developing microcracks in the mold core. The reject rate at that point was 0.3% with nothing in the production data suggested a problem was building.
Because our check caught it early, the repair was contained. Wanox performed laser cladding repair on the core at a cost of RMB 20,000, with three days of downtime. Left unaddressed, the mold would have developed severe sticking and flashing by 700,000 cycles, with estimated losses exceeding RMB 300,000 across lost production, emergency air freight, and customer penalties. The difference between those two outcomes was one scheduled maintenance check.
This is not an exceptional case and is what structured maintenance catches before the production data shows anything at all.
What to Ask Your Manufacturer Now
A procurement lead who has never seen a maintenance record from their manufacturer has no way of knowing whether this kind of early detection is happening on their tooling. Most find out it was not happening when something goes wrong.
Four questions will tell you what you need to know before that point.
- What is the preventive maintenance interval for my mold, and when was the last service performed?
- Can you provide maintenance records for the past twelve months, including a list of replaced parts?
- If I request a third-party mold audit, can it be arranged at your facility?
- How is the cycle count recorded, and can I view it at any time?
A manufacturer with a functioning maintenance system will answer all four questions without hesitation and produce the records to support them. If the answers are slow, partial, or blocked by factory policy, the mold is probably in the same condition as the records: missing, incomplete, or worse than anyone is admitting.
What Good Documentation Looks Like

If your manufacturer cannot produce structured maintenance records, you have no way of knowing the condition of your tooling at any point in its life.
After each maintenance service, Wanox issues three documents.
- A Mold Maintenance Report recording the date, cycle count, and results of every inspection
- A Replaced Parts Log listing every component changed with specifications and before-and-after photographs
- A Post-Maintenance Sample Report confirming the mold has been restored to acceptable condition, with dimensional data attached.
These documents exist so that the condition of your mold is never a matter of opinion.
When a Mold Needs More Than Maintenance
Some molds reach a point where maintenance is no longer the answer. The decision between refurbishment and replacement carries real budget consequences and must be based on evidence, not a manufacturer’s preference.
How Wanox makes the call
Level 1: Instrument-based inspection to locate and measure wear, cracks, or corrosion at the component level.
Level 2: Remaining life estimation based on the mold’s material, treatment history, and cycles already run.
Level 3: Cost comparison. If refurbishment costs less than 40% of a new mold and delivers at least 50% of remaining life, Wanox recommends refurbishment. If the quote exceeds 65% of new mold cost and remaining life falls below 30%, replacement is the recommendation.
Replacement becomes the only option when the mold base is permanently warped, when the cavity or core has been heavily welded more than three times, when cooling channels are too corroded to restore, or when the original design has a fundamental flaw that no repair addresses.
The recommendation comes with a written rationale either way. A procurement lead receiving a verbal opinion with no supporting data is not receiving a recommendation, and instead, they are being managed.
What Changes When You Ask These Questions

Tooling maintenance is an asset protection question, and the answers sit entirely with the manufacturer running your production. The quality problems that arrive without warning are rarely random and are the end of a process that started long before the reject rate moved.
The manufacturers who will answer these questions without hesitation are the ones already running the checks.
Contact Us
Talk to Wanox about your tooling before the next order ships.



